You built a guitar. With your own two hands. You sanded, finished, soldered, and set it up, and it sounds fantastic. Then one day the strings go dull, or the high E snaps mid-solo, and suddenly you're staring at six tuning posts like they owe you money.
Relax. Restringing is the easiest maintenance job you'll ever do on your DIY guitar kit build, and it's also the one people botch most often. Bad string changes cause slipping tuners, buzzing, and that fun thing where your guitar goes sharp every time you look at it. Here's how to do it right the first time.
What You Need (Spoiler: Not Much)
If you've already done a guitar kit build, you own most of this stuff. If not, it's all cheap:
- A fresh set of strings in the gauge you like. Stick with what the guitar was set up for unless you're ready to tweak the truss rod and intonation too.
- Wire cutters for trimming the excess. Please don't use your good woodworking chisels. We've seen things.
- A string winder. Optional, but it turns five minutes of wrist cranking into thirty seconds.
- A tuner. Clip-on or app, either one works.
- A soft cloth and maybe some fretboard conditioner if your board is unfinished rosewood or similar.
Step 1: Off With the Old Strings
Loosen each string until it's floppy, then snip it in the middle and pull the pieces out. Old advice said to never take all the strings off at once. On a bolt-on electric with a fixed bridge, it's fine. Honestly, it's the perfect excuse to clean the fretboard and frets while nothing is in the way.
One exception: if you've got a floating tremolo, change strings one at a time or block the trem first. Otherwise the bridge tilts forward and you'll get to redo part of your setup. Fun!
While the strings are off, give the tuners a quick check. Snug any loose nuts or screws by hand-tight plus a nudge. Don't crank them. You did not just finish that headstock to crack it now.
Step 2: Load the Bridge End
Feed each new string through the bridge or body ferrules, depending on your design. Pull it all the way through so the ball end seats fully. If the ball end isn't seated, the string will "settle" later and you'll be retuning for a week wondering what you did wrong.
Pro tip: give each string a little tug toward the headstock once it's through. You should feel it click into place.
Step 3: Wind It Right at the Headstock
This is where most string changes go sideways. The goal is a solid grip on the post with just enough wraps, not a bird's nest of steel.
- Leave the right amount of slack. Pull the string past its tuning post by about two to three inches for the wound strings and a bit more for the plain ones. That gives you roughly two to three wraps on the wound strings and three to four on the unwound ones.
- Thread and kink. Push the string through the post hole, then bend it sharply so it can't slide back out.
- Wind downward. Each wrap should go below the previous one. This increases the break angle over the nut, which helps tone and sustain and keeps the string seated in its slot.
- Wind in the right direction. On a six-in-line headstock, strings typically wind counterclockwise as you look at the face of the headstock, so they come off the inside of the post in a straight line to the nut.
- Optional locking wrap. For plain strings especially, pass the loose end under the string before your first wrap, then pull it up tight so the string pinches itself. Old trick, works great.
Trim the excess, leaving about a quarter inch. Long whiskers poking out of the headstock look rough and love stabbing your fingers.
Step 4: Stretch, Tune, Repeat
New strings stretch. That's physics, not a defect in your DIY guitar kit. Tune to pitch, then gently pull each string up away from the fretboard a few times along its length. Retune. Repeat two or three times until it stops going flat.
Skip this step and you'll be retuning between every song for the next two days. Do it and your guitar settles in within minutes.
If you changed string gauge, now is the time to check neck relief and intonation. Heavier strings pull harder on the neck, and lighter ones may cause buzzing. That's not a crisis, just a quick adjustment.
When Should You Restring?
There's no strict rule, but here are signs it's time:
- The strings feel gritty or look discolored.
- Your tone sounds dull, like someone put a blanket over the amp.
- The guitar won't stay in tune or intonate properly anymore.
- You can't remember the last time you changed them. That counts.
Players who gig or play daily might restring every few weeks. Weekend warriors can usually go a couple of months. Wiping strings down after you play helps them last much longer.
Your Build, Your Maintenance
Here's the beauty of choosing to build your own guitar: you already know every part of it inside and out. Changing strings isn't some mysterious chore you pay a shop to do. It's just another five-minute job on an instrument you made yourself.
If you haven't started your first build yet, or you're itching for build number two, check out the full lineup of DIY guitar kits at Vibeworks Guitars. Every kit comes with the parts you need to assemble your own guitar, whether you're a first-timer or a woodworker looking for a new project. Grab one, build it, and then come back here when it needs fresh strings.